Smart Product Operation Guide – Feature Introduction

1.  Control LED Grow Light

1. Manual Mode

• Turn the light on/off directly from the app.
• Adjust brightness manually.

1. Timer Mode

• Choose control type: Dimming Ratio or PPFD.
  • Dimming Ratio:
    • Click Running Stage to set working hours and brightness levels.
    • Up to 5 different stages can be programmed.
  • PPFD Mode:
    • Requires a PPFD sensor.
    • After selecting PPFD, click Running Stage to set working hours and target PPFD value.
    • The light will automatically adjust brightness to maintain the target PPFD.
    • Up to 5 different stages can be programmed.

1. Sunrise/Sunset Mode

• Set sunrise and sunset duration.
• The light will gradually brighten from 10% to maximum brightness before the start time, and dim gradually after the end time until fully off.

2.  Control Inline Fan

• Turn the fan on/off via the app.
• Adjust fan speed manually.

1. Timer Mode

• Click Running Stage to set operating times and fan speeds.
• Up to 5 different stages can be programmed.

1. Cycle Mode

• Configure the following:
  • Start Time
  • Running Duration: Fan run time per cycle.
  • Pause Duration: Fan off time per cycle.
  • Loop Count: Number of cycles before midnight.
• The fan will follow the set cycle of running and pausing.

1. Environmental Mode

• Choose one of three environmental strategies:
  • Temperature & Humidity – Operates when either goes beyond set range.
  • Temperature Priority – If both cannot be maintained, prioritize temperature control.
  • Humidity Priority – If both cannot be maintained, prioritize humidity control.
• Set fan speed and oscillation angle.
• Based on sensor readings, the fan will auto-adjust to maintain the ideal environment.

1. Standby Speed

• When selected, the fan will continue running at standby speed even during off-time.
  • 4-inch fan: 205 CFM
  • 6-inch fan: 402 CFM

3.  Control Clip Fan

1. Manual Mode

• Turn the clip fan on/off via the app.
• Adjust fan speed and oscillation angle manually.

1. Timer Mode

• Click Running Stage to set operating times, speeds, and oscillation angles.
• Up to 5 different stages can be programmed.

1. Cycle Mode

• Configure the following:
  • Start Time
  • Running Duration: Fan run time per cycle.
  • Pause Duration: Fan off time per cycle.
  • Loop Count: Number of on/off cycles (limited to before 23:59 of the same day).
• The fan will follow the set cycle of running and pausing.

1. Environmental Mode

• Choose one of three environmental strategies:
  • Temperature & Humidity – Operates when either goes beyond set range.
  • Temperature Priority – If both cannot be maintained, prioritize temperature control.
  • Humidity Priority – If both cannot be maintained, prioritize humidity control.
• Set fan speed and oscillation angle.
• Based on sensor readings, the fan will auto-adjust to maintain the ideal environment.

1. Natural Wind Mode

• Simulates natural wind patterns.
• Fan cycles through 5 speed levels, gradually decreasing from the current level down to Level 1, then increasing back to maximum speed.

4. Control Humidifier / Dehumidifier

1. Manual Mode

• Turn the device on/off directly from the app.
• Manually adjust the gear level.

1. Timer Mode

• Click Running Stage to set the operating times of the device.
• Up to 5 different time periods can be programmed.

1. Cycle Mode

• Configure the following:
  • Start Time
  • Running Duration: Device running time per cycle.
  • Pause Duration: Device off time per cycle.
  • Loop Count: Number of cycles before midnight.
• Once set, the device will automatically turn on at the defined start time and follow the programmed running and pausing cycle.

1. Environmental Mode

• After selecting the environmental strategy:
  • When humidity is higher than the target value, the dehumidifier will automatically start to restore optimal conditions.
  • When humidity is lower than the target value, the humidifier will automatically start to reach the ideal environment.

Scene Setting

1. Create and Name a Scene

• Create a new scene and assign a name for easy identification between different growth stages.

1. Set Scene Time and Environmental Parameters

• Choose the scene start time.
• Select the plant growth stage (Planting Stage).
• Define the stage cycle (Stage Duration).
• Configure environmental settings such as:

1. Lighting Setting

• Select a lighting control mode:

• If using Dimming Ratio Mode:

• If using PPFD Mode:

• Note: If the target PPFD value exceeds the lamp’s maximum achievable PPFD, the light will operate at maximum brightness.

1. Sunrise / Sunset Mode

• Set the sunrise and sunset transition duration (e.g., 30 minutes).
• Before the ON time, brightness will gradually increase from 10% to the preset maximum.
• After the OFF time begins, brightness will gradually decrease until fully off after the set duration.

1. End Reminder

• Set a reminder before the end of the current growth stage to ensure timely transition to the next stage.